|
|
Laser-Positioning System PSD-01
|
Characteristics:
. High resolution
(10μm)
. Operational range
up to 25m
. Suitable for
operation by mains or battery power supply
. Short measuring
cycle
. Menu controlled
. RS232-interface
for protocol
. Portable, solid
design
. Mechanical
adaptation to suit your application available
![[Immagine linea di divisione]](gif_images/div.gif)
Short description
The positioning
system PSD 01 has been developed especially for the alignment of
precise machinery. Using a visible laser, the equipment can be adjusted
during installation or realigned during maintenance with a high degree of
accuracy.
The system
includes a laser with an accumulator-box , a receiver and a basic operation
and indication system with a integrated mains adapter. The modulated laser
emits a visible beam which is received by a 2-dimensional sensor. The
detector converts the geometrical data into a signal current. These signals
are fed to the base unit by cable and interpreted in the micro processor.
The co-ordinates, selected parameters and menu functions are shown on a
large LCD display.
The position of
the laser is indicated numerically and in graphic format as a circle within
a scaled graticule. There are four function key pats underneath the display
to permit the following adjustments: Display of absolute-/relative-centers,
ZOOM -factor for graphic display, centre alignment of graticule, adjustment
of filter response , LED-indicators ON/OFF.
The LED-indicator
uses eight light emitting diodes arranged within a square which indicate the
offset position of the laser relative to the centre. This is useful when
making coarse adjustments over long distances. Additionally, all measurement
data is fed to an RS232 interface enabling computer records and protocols to
be kept, if desired.
With accumulators
fully charged, the system is operationally autonomous for a minimum of five
hours. Except for recharging and the occasional cleaning of the laser
aperture there is no requirement for maintenance.
Mechanical
dimensions of sender and receiver can be adjusted to meet special
application requirements as long as the indicated minimal dimensions are
considered. Also possible is the development of a specific measuring system
based on PSD 01 technology.
Basic system data
|
| Power supply |
12 Vcc ±10% |
| Power supply from battery |
7,5 Vcc |
| Consumption |
700mA max. |
| Display |
LCD 128x128 |
| Precision |
10µm |
| Warm up time |
30 second |
| Filter constant |
0,1...50 second adjustable |
| Accumulator |
6 X NiMH, 2.6Ah |
| Recharge time |
3 ore |
| Connection Emitter |
LEMO ERN.00.250.CTL |
| Connection Receiver |
LEMO ERA.1S.306.CLL |
| Serial output |
RS232 9600 baud |
| Degree of protection |
IP30 |
![[Immagine linea di divisione]](../ilee/gif_images/div.gif)
Power supply
|
| V in |
100...240 Vac |
| V out |
12 Vcc ±10% |
Emitter
|
| Power supply |
4...6 Vcc |
| Consumption |
100 mA max |
| Laser Class |
2 IEC |
| Laser power output |
<1 mW |
| Wave lenght |
650 nm |
| Warm up time |
<5 min. |
| Frequency modulation |
2KHz |
| Degree of protection |
IP65 |
| Connection |
LEMO 2 |
Receiver
|
| Power supply |
20 Vcc ±10% |
| Consumption |
<30 mA |
| Active surface area |
Ø 10 mm 1) |
| Degree of protection |
IP65 |
| Connection |
LEMO 6 poli |
|
|
| 1) standard, other dimensions on request |
Download technical
specification
Back to laser main
page
Aggiornato il 19 luglio 2004
|